How to Use Electric Confetti Cannons

Your Guide to Using Electric Confetti Cannons
At R&B Confetti, we're more than just confetti cannons. We craft memories. With electric cannons, you can fire both confetti and streamers at the push of a button, creating instant joy and spectacular effects.

Follow this step-by-step guide to set up and safely operate your Electric Confetti Cannon.

• Electric confetti cannon unit
  
  
• CO₂ cartridges + piercing unit
  
  
• Compression caps and black compression tape
  
  
• Pre-sleeved confetti or streamer consumables
  
  
• Power source (110V controllable outlet)
  
  
• Safety cable

General Safety Precautions

• Never aim the cannon at people or animals.
  
  
• Never leave the cannon unattended while loaded or powered.
  
  

CO₂ Cartridge Handling

• CO₂ cylinders become extremely cold during use — risk of frostbite.
  
  
• Always bleed off remaining CO₂ before removing the piercing unit.
  
  
• Failure to bleed CO₂ may cause o-ring failure or injury.
  
  

Supervision

• Only trained crew should operate.
  
  
• Maintain constant supervision when unit is charged and connected.

Confetti or Streamers

1. Cut open one end of the plastic sleeve.
   
   
2. Insert sleeve into barrel.
   
   
3. Method 1 (Drop): Hold barrel upright and drop contents in.
   
   
4. Method 2 (Slide): Pull sleeve out while sliding contents into barrel.
   
   
5. Remove the sleeve completely.
   
   

Compression Cap

1. Position cap over open end of barrel.
   
   
2. Wrap black compression tape tightly around the cap and barrel.
   
   
3. Press along tape with your thumb to seal airtight.
   
   
4. This creates a pressure chamber for maximum launch distance.

1. Ensure the piercing unit valve is fully closed.
   
   
2. Hold the piercing unit firmly.
   
   
3. Screw threaded CO₂ cartridge into the piercing unit quickly.
   
   
4. Continue tightening until cartridge pierces (you’ll hear or feel it).
   
   
5. Confirm full piercing for consistent, powerful shots.

1. Ensure the barrel is loaded and CO₂ cartridge installed.
   
   
2. With power OFF, connect the cannon to a controllable 110V outlet.
   
   
3. Attach a piercing unit to quick-connect fitting.
   
   
4. Slowly open the valve on the piercing unit to charge the cannon with CO₂.
   
   
5. Attach loaded barrel to quick-connect fitting.
   
   
6. Connect the safety cable from unit to barrel.

• Adjust barrel angle for desired projection.
  
  
• Cannon is now charged and ready.
  
  
• Activate power switch for minimum 5–6 seconds:
  
  
  • Ensures complete and powerful launch.
    
    
  • Instant fires when it receives power.

• Place the cannon 15–25 feet from the coverage area.
  
  
• Bulk of confetti covers 25–35 feet out.
  
  
• Confetti spreads wide while floating.
  
  
• For maximum impact: use cannons on both sides of the target area.

• Place the cannon ~30 feet from the coverage area.
  
  
• Streamers soar over 65 feet in a wide “V” pattern.
  
  
• For dramatic effect: fire cannons on opposite sides to cross streamers midair.

• Cannon won’t fire → check CO₂ piercing and electrical connection.
  
  
• Weak blast → ensure compression cap is airtight and CO₂ is fully pierced.
  
  
• Uneven shot → check confetti loading (loose, not packed).

• How far does it shoot? → Confetti 35 ft+, Streamers 65 ft+.
  
  
• What power is required? → Standard 110V outlet (controllable).
  
  
• Do I need CO₂ every time? → Yes, CO₂ cartridges are required to fire.
  
  
• Can I reuse the barrel? → Yes, but always reload with fresh consumables and reseal with cap + tape.

Let the Fun Fly!
With electric confetti cannons, you’re not just firing effects — you’re creating unforgettable moments. Our team is always here to help with setup, troubleshooting, or consumable guidance.