Professional Confetti Cannon Guides

Welcome to our comprehensive guide for professional confetti cannons. This page provides detailed, step-by-step instructions for setting up and operating your equipment, ensuring a safe and spectacular event.

Use the table of contents below to jump directly to the guide you need.

How to Use Your Continuous Flow Confetti Cannon
How to Use Your Electric Confetti Cannon
How to Use Your Stage Confetti Cannon
How to Use Your T-Shirt Cannon

How to Use Your Continuous Flow Confetti Cannon

This guide will walk you through the simple, step-by-step process of setting up, loading, and safely operating your continuous flow confetti cannon.

Getting Started

Before you begin, ensure you have all the necessary components for a successful event:

The Cannon System:

The continuous flow confetti cannon unit

Consumables:

Bulk confetti
A 50 lb Liquid CO2 Siphon Tank

Pre-Launch Checklist

Verify that all components are present and undamaged.
Ensure your CO2 tank is full and securely placed in an upright position.
Confirm the area is clear of all obstructions and spectators are at a safe distance.

Step-by-Step Operating Instructions

Follow these steps carefully to ensure a fun and safe experience.

Connect the CO2 Tank:
- First, confirm the white plastic o-ring is in place on the CO2 nut.
- Attach the CO2 nut to the CO2 tank. Use a wrench to tighten it securely.
- Connect the ball valve to the cannon's horn intake valve. Hand tighten, then use a wrench to tighten an additional 1/4 turn only. Do not overtighten.
- Ensure the ball valve is in the closed (off) position.
- Slowly open the CO2 tank valve to pressurize the system. You will hear a hiss as the gas fills the cannon.
Load the Confetti:
- Pour the confetti loosely into the hopper.
- For optimal results, do not pack the confetti down.
- The hopper holds between 5-10 lbs of confetti. You can add more confetti as needed while the unit is operating.
Operate the Confetti Cannon:
- To start the confetti flow, slowly open the ball valve.
- Adjust the valve to control the flow, from a powerful blast to a light shower.
- To stop the confetti flow, simply close the valve.

Important Safety Note: Do not open the valve fully or the unit will freeze up and clog.

How to Use Your Electric Confetti Cannon

This guide will walk you through the simple, step-by-step process of setting up, loading, and safely operating your new electric confetti cannon.

Getting Started

Before you begin, ensure you have all the necessary components for a successful event:

The Cannon System:

The electric confetti cannon unit
A controllable on/off 110v power source

Consumables:

Confetti or streamer sleeves
CO2 cartridges
Compression caps
Compression tape

Pre-Launch Checklist

To ensure a safe and successful launch, quickly review this checklist before powering on the cannon.

Verify all components are present and undamaged.
Plug the cannon into a reliable power source.
Confirm ceiling height is 15 feet or higher.
Ensure the area is clear of all obstructions and that spectators are at a safe distance.

Step-by-Step Operating Instructions

Follow these steps carefully to ensure a fun and safe experience.

Prepare the Confetti Barrel:
- Slide the confetti or streamers completely into the barrel.
- Place a compression cap onto the end of the barrel.
- Secure the cap to the barrel with compression tape.
- Rub the compression tape with your thumb to create a firm seal.
Position and Attach the Barrel:
- Position the unit on a flat, level surface.
- Confirm that the trajectory area is clear of all obstructions.
- Connect the loaded barrel using the quick-disconnect fittings, making sure it is securely attached.
- Adjust the angle of the barrel as needed.
- Attach the safety cable to the barrel for added security.
Load CO2 and Pressurize:
- Insert the CO2 Cartridge: With the piercing unit in the closed position, hold it in one hand. Quickly and securely screw the CO2 cartridge completely into the unit to prevent any loss of gas.
- Attach the Piercing Unit: Connect the loaded piercing unit to the cannon base using the quick-disconnect fittings.
- Open the Valve: Once the unit is securely attached, slowly open the piercing unit valve to pressurize the system.
Power On and Fire:
- Ensure your power source is off before plugging in the unit.
- Plug the unit into the power source.
- Turn the power on to instantly fire the confetti cannon. Be sure to leave the power on for 4-5 seconds to ensure a complete and powerful burst.

The cannon is now ready to be reloaded after firing.

How to Use Your Stage Confetti Cannon

This guide will walk you through the simple, step-by-step process of setting up, loading, and safely operating your stage confetti cannon.

Getting Started

Before you begin, ensure you have all the necessary components for a successful event:

The Confetti Cannon System:

The stage confetti cannon unit

Consumables:

Confetti or streamer sleeves
CO2 cartridges
Compression caps
Compression tape

Step-by-Step Operating Instructions

Follow these steps carefully to ensure a fun and safe experience.

Prepare the Confetti Barrel:
- Slide the confetti or streamers completely into the barrel.
- Place a compression cap onto the end of the barrel.
- Secure the cap to the barrel with compression tape.
- Rub the compression tape with your thumb to create a firm seal.
Load CO2 Cartridge:
- Insert the CO2 Cartridge: Securely screw the CO2 cartridge completely into the trigger assembly.
Aim and Fire:
- Holding: Hold the cannon with a firm grip in one hand.
- Aiming: Point the barrel upwards around 45°. Ensure the trajectory is free and clear of all objects and people.
- Firing: Pull the ring trigger quickly and firmly in one motion, without hesitation.

How to Use Your T-Shirt Cannon

This guide will walk you through the simple, step-by-step process of setting up, loading, and safely operating your new t-shirt cannon.

Getting Started

Before you begin, ensure you have all the necessary components for a successful event:

The t-shirt cannon unit
A 5 lb CO2 tank
T-shirts or other soft items to launch

Pre-Launch Checklist

Verify that all components are present and undamaged.
Ensure your CO2 tank is full.
Confirm the area is clear of all obstructions and that spectators are at a safe distance.

Step-by-Step Operating Instructions

Follow these steps carefully to ensure a fun and safe experience.

Prepare T-Shirts and Secure the Tank:
- Folding T-Shirts:
  - Lay the t-shirts out flat.
  - Fold the sleeves in towards the center of the shirt.
  - Starting at the top, roll the shirt tightly.
  - Place three rubber bands on the t-shirt (one in the middle, and one on each end) to keep it rolled up.
- Secure CO2 Tank:
  - Place the CO2 tank in the backpack harness and tighten the straps securely.
Connect the System:
- Connect the CO2 Tank:
  - First, confirm the white plastic o-ring is in place on the CO2 nut.
  - Attach the CO2 nut to the CO2 tank. Use a wrench to tighten it securely.
  - Connect the hose to the trigger assembly. Hand tighten, then use a wrench to tighten an additional 1/4 turn only. Do not overtighten.
  - Slowly open the CO2 tank valve to pressurize the system. You will hear a hiss as the gas fills the cannon.
- Attach the Barrel:
  - Slide the barrel's quick-disconnect fitting into the fitting on the trigger. The two levers with rings will flip up when you slide the fittings together.
  - Once the barrel is fully seated, pull both rings back fully to lock the fittings.
  - Attach a safety cable from the trigger to the barrel.
- Secure the Backpack:
  - Place your arms through the straps of the backpack harness and adjust the straps for a comfortable fit.
  - Secure the waist straps using the provided buckle.
Load and Fire:
- Load the T-Shirts:
  - Using a pushing and twisting motion, slide the rolled t-shirts into the barrel.
  - Slide the t-shirts completely into the barrel for the best distance shot.
- Fire the Cannon:
  - Hold the barrel in one hand with a firm grip.
  - Hold the trigger assembly with your other hand.
  - Pull the trigger in one quick and firm motion to fire the t-shirts.

The cannon is now ready to be reloaded after firing.